我們店鋪的切割機種類有很多，動力有柴油，汽油，電動的，有單用的，還有切割刻紋一體機，有普通款的，還有威克款的，質量方面您大可放心，重點是看哪款動力適合您，外觀看您喜歡什么樣式的！

There are many kinds of cutting machines in our shop, such as diesel, gasoline, electric, single-use, and all-in-one cutting and engraving machines, including ordinary ones and wick ones, you can rest assured in terms of quality, the focus is to see which type of power suits you, look at what style you like!
我們做出來的原則就是結構簡單，操作靈活，讓您愛不釋手！
We made the principle is simple structure, flexible operation, let you Hands All Over!

混凝土切割機產品用途：
專為市政建設改選、路面維修施工、機場路面切割、通訊工程埋設及地板、車道等現場作業專業切割。?主要用于切割混凝土，水泥，地板及石制路面，切割路面收縮縫或破損路面。是使用金剛石鋸片切割混凝土路面、大理石板、水磨構件等脆性材質的鋸切工具。
For municipal construction re-election, road maintenance and construction, airport road cutting, communications engineering buried and floors, driveways and other field operations professional cutting. It is mainly used for cutting concrete, cement, floor and stone pavement, cutting pavement contraction joints or broken pavement. Diamond Blade is a sawing tool for cutting brittle materials such as concrete pavements, marble slabs, and water mill components.


水冷柴油切割機參數：
機器型號：500型
鋸片直徑 ：400-500mm
較大切深 ：180mm
鋸片線速度：36-45m/s
水箱 ：37L
包裝尺寸：1500?500?900mm
重量：260KG
這款500款的我們采用15馬力的水冷柴油機，強勁有力
水箱采用的也是加厚的，橡膠手把耐磨，手柄輪可控制鋸片的切割哦，好方便的一款！
移動方便，減少了扯電纜線的麻煩！
性能穩定，不用擔心，直接下單!

Section 500 we use 15 horsepower water-cooled diesel engine, strong water tank is also thick, rubber handlebar wear-resistant, handle wheel can control the cutting blade Oh, a good convenience! Easy to move, reduce the trouble of pulling cable! Stable performance, do not worry, direct order!

l混凝土切割機使用方法：
1、開機前應檢查各部分螺栓，螺母有無松動；檢查電源、接線有無漏電現象；鋸片旋轉方向與防護罩標注方向是否一致，檢查無誤后方可開機工作。
?2、開機工作前，水箱應注滿水；工作時，應及時擰開水管開關，向鋸片噴水冷卻。
3、切割深度由手輪調節，用手輪轉動推把前面的手輪，使螺桿絲母旋轉升降，于是前輪高低位置改變，鋸片隨之升高或下落。
?4、切割前，鋸片應離開地面，鋸片正常運轉后，應慢慢旋轉手輪使機頭下落，當鋸片切刀予定深度后，即可向前推進，此時，導向桿應先放下，使導向輪著地。
5、切割行進時，雙目應注視導向輪以掌握切縫方向，雙手推動推把，使導向輪沿予定的切割線前進，保證切口的平直性。
?6、由于行進過速切割過深或遇到硬物質時，電機因過載使鋸片轉速下降，此時應停止推進或減慢送進速度，以保護電機、柴油機、汽油機和鋸片不受損壞。
來砸單吧，朋友們，使勁砸單，熱烈歡迎！
Concrete cutting machine use method: 1, before starting the machine should check all parts of bolts, nuts loose; check the power supply, wiring leakage phenomenon; saw blade rotation direction and protective cover marked direction is consistent, do not start the machine until it has been checked correctly. 2. Before starting the machine, the water tank should be filled with water; while working, the water pipe switch should be turned on in time to spray water to the saw blade for cooling. 3, cutting depth by hand wheel adjustment, with hand wheel rotation push the hand wheel in front, screw nut rotation up and down, so that the front wheel high and low position change, the saw blade then up or down. 4, before cutting, the saw blade should leave the ground, after the saw blade normal operation, should slowly rotate the handwheel to make the machine head fall, when the saw blade blade to be given a certain depth, can advance, at this time, the guide rod should first put down, so that the guide wheel landing. 5. When cutting, both eyes should look at the guide wheel to grasp the direction of the cutting seam, and both hands should push the handle to make the guide wheel advance along the fixed cutting line to ensure the straightness of the incision. 6, because of moving too fast cutting too deep or encountered hard material, the motor due to overload to reduce the blade speed, at this time should stop or slow down the feed speed, to protect the motor, diesel engine, gasoline engine and saw blade from damage. HIT IT, folks! HIT IT HARD! GIVE IT UP!

聯系人：陳經理
地址：山東省濟寧市任城區金宇路4號
手機：13165175381