摩擦磨損試驗機廠家

摩擦磨損試驗機廠家  功能特點：

1、試樣尺寸： 30mm?7mm?6mm

2、轉動速度： 0-500轉/分 （可調）

3、負 荷： 196N ? 0.1%（可增至392N）

4、摩擦環尺寸：￠40?10mm ，倒角0.5?45?，外圓表面與內圓同心度偏差小于0.01

5、摩擦環材質：45號鋼,淬火,熱處理HRC40-45,外圓表面光潔度▼8

6、摩擦力矩： 0--4N?m

7、砝碼重量：4KG砝碼一件，1KG砝碼4件，可實現重量疊加功能。

Functional characteristics:

1, sample size: 30mm x 7mm x 6mm

2, rotation speed: 0-500 turn / points (adjustable)

3, load: 196N 0.1% (can be increased to 392N)

4, the size of the friction ring is: 40 x 10mm, chamfer 0.5 * 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.01.

5, friction ring material: 45 steel, quenching, heat treatment HRC40-45, round surface finish 8

6, friction moment: 0--4N. M

7, weight weight: 4KG weight one, 1KG weight 4, can achieve weight superposition function.

試驗報告

試驗報告應包括下列內容：

A.塑料名稱、規格、牌號、生產廠；

B.試樣的制備方法，摩擦表面狀況，測定的試樣個數；

C.環境溫度、溫度及狀態調節條件；

D.圓環材質、硬度、光潔度和外徑尺寸；

E.試驗負荷；

F.試驗結果：磨痕寬度或體積磨損及摩擦系數的測定結果；

G.試驗日期、人員。

Test report

The test report should include the following contents:

A. Plastic name, specification, brand, and manufacturer;

B. The preparation method of the sample, the condition of the friction surface, and the number of samples measured;

C. Environmental temperature, temperature and state regulation conditions;

D. Circular ring material, hardness, smoothness, and outer diameter size;

E. Test load;

F. Test results: Measurement results of abrasion width or volume wear and friction coefficient;

G. Test date and personnel.

精度Precision:

1、速度精度：1%

2、負荷精度：0.5%

3、摩擦力矩精度：1%

4、計數器精度：1S

5、傳感器測量精度：1% FS

Precision:

1. Speed precision: 1%

2. Load precision: 0.5%

3. The precision of friction moment: 1%

4. Counter precision: 1S

5. Sensor measurement accuracy: 1% FS

功能：

本廠生產的計算機控制塑料滑動摩擦試驗機是在現有電子塑料滑動摩擦試驗機的基礎上又增加了很多試驗功能，可以同時顯示扭矩-時間曲線，隨意設定試驗次數，顯示當前試驗次數，設定時間及當前試驗時間等多種功能，本機還配有彩色打印機，可以打印出帶有曲線，表格數據，試驗單位名頭的精美的試驗報告單。

Function:

The computer controlled plastic sliding friction test machine produced by our factory is on the basis of the existing electronic plastic sliding friction test machine, and has added a lot of test functions. It can display the torque time curve at the same time, set the test times at will, display the current test times, set the time and the current test time and other functions, this machine is this machine. It also has a color printer, which can print out exquisite test reports with curves, table data and test units.

試驗步驟

1、圓環應清除油污，貯存于干燥缸內以防生銹。

2、試樣經狀態調節后用感量為0.1毫克的分析天平稱取其質量（M1）。

3、把試樣裝進夾具，摩擦面用角尺校正并使它與圓環的交線外于試樣正中。裝好摩擦力矩記錄紙，開機校好零點。

4、再次用乙醇、丙酮等不與塑料起作用的溶劑仔細清除試樣和圓環上的油污，此后不準再用手接觸試樣和圓環的表面。

5、平穩地加荷至選定的負荷值。

6、對磨2小時后停機卸負荷，取下試樣和圓環，清理試樣表面后，用精度不低于0.02毫米的量具測量磨痕寬度，或在試驗環境下存放1小時后稱取試樣質量（m2)。

7、讀取摩擦力矩值。

Experimental steps

1. The circular ring should be cleaned of oil stains and stored in a drying cylinder to prevent rusting.

2. After adjusting the state of the sample, weigh its mass (M1) using an analytical balance with a sensitivity of 0.1 milligrams.

3. Insert the sample into the fixture, calibrate the friction surface with an angle ruler, and ensure that its intersection with the circular ring is outside the center of the sample. Install the friction torque recording paper and start the machine to calibrate the zero point.

4. Carefully remove the oil stains on the sample and the ring using solvents such as ethanol and acetone that do not work with plastic. After that, do not touch the surface of the sample and ring with your hands.

5. Smoothly load to the selected load value.

6. After grinding for 2 hours, stop the machine to unload the load, remove the sample and ring, clean the surface of the sample, measure the width of the grinding mark with a measuring tool with an accuracy of not less than 0.02 millimeters, or weigh the sample mass (m2) after storing it in the test environment for 1 hour.

7. Read the torque value of friction force.

狀態調節

狀態調節按GB2918-82《塑料試樣狀態調節和試驗的標準環境》進行，溫度為23?5攝氏度，溫度為50?10%。

摩擦磨損定義

1、摩擦：兩物體接觸表面間產生阻礙切向相對移動的現象稱為摩擦。

2、滑動摩擦：兩接觸物體接觸點具有不同速度時之摩擦。

3、摩擦力：兩物體摩擦時相對移動的阻力。

4、摩擦系數：阻礙兩物體相對運動的摩擦力對作用到物體表面的法向力之比。

5、磨損：物體相對運動時相互接觸表面的物質不斷損失或產生殘余變形稱為磨損。

Definition of Friction and Wear

1. Friction: The phenomenon of hindering tangential relative movement between two surfaces in contact is called friction.

2. Sliding friction: Friction between two objects in contact at different speeds.

3. Friction: The resistance to relative movement between two objects when they rub against each other.

4. Friction coefficient: The ratio of the frictional force that impedes the relative motion of two objects to the normal force acting on the surface of the object.

5. Wear: The continuous loss or residual deformation of substances on the surfaces in contact with each other during relative motion of objects is called wear.

主要配置及附件：（計算機控制）

1、試驗主機一臺

2、高精度扭矩傳感器一只

3、計算機數據采集卡一塊

4、計算機一臺（品牌）

5、彩色激光噴墨打印機一臺

6、計算機控制軟件一套

7、4Kg 砝碼兩件（備用一套）

8、標準磨擦環四件（備用兩件）

9、產品使用說明書一份

10、產品合格證

11、產品裝箱單一份

12、整機重量：約87 公斤

Main configuration and accessories: (computer control)

1. A test host

2. A high precision torque sensor

3. One piece of computer data acquisition card

4. One computer (brand)

5. A color laser inkjet printer

6. A set of computer control software

7, two 4Kg weights (a spare set)

8, four standard friction ring (two spare)

9. One copy of the product instructions

10. Product qualification certificate

11. Packing a single part of the product

12, the weight of the whole machine: about 87 kilograms

售后服務。

1、保修期內非人為損壞的零部件免費更換，保修期內接到用戶邀請后，最遲響應時間為4小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法。

2、提供實時的遠程診斷和維護服務。

3、每年進行客戶回訪。

4、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后2天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。

5、保修期內人為損壞的零部件按采購（加工）價格收費更換。

6、軟件升級：終生免費提供新版本控制軟件。

7、安裝及調試合格后，自客戶簽字認可之日起，我方對于提供的產品免費保修三年。保修期滿后，我方將繼續跟蹤服務，客戶享受終生維修，負責及時提供必要的售后服務、技術咨詢。

8、產品交貨期：盡量按用戶要求，若有特殊要求，需提前完工的，我公司可特別組織生產、安裝，力爭滿足用戶需求。

9、保修承諾：我司對本次協議供貨有效期內所提供的所有產品保質期 ，有效期內所提供的產品，提供正常工作日全天侯服務，終身技術服務支持。

10、響應時間：保修期內，產品若發生故障，在接到貴公司報修后，24小時內幫客戶解決問題。

11、服務體系：作為設備供應商本公司對本次招標所提供的產品提供保障體系： 當設備出現故障，必要時將派指定的專業技術員在規定時間內上門維修或寄修，產生的運費由本公司承擔。

12、產品價格承諾 1、在同等競爭條件下，我公司在不以降低產品技術性能、更改產品部件為代價的基礎上，真誠以最優惠的價格提供給貴方。 2、在保修期內供方將免費維修和更換屬質量原因造成的零部件損壞，保修期外零部件的損壞，提供的配件只收成本費，由需方人為因素造成的設備損壞，供方維修或提供的配件均按成本價計。

13、售后服務保證

公司實力保障：本公司有完善的售后服務體系;

功能特點：

1、試樣尺寸： 30mm?7mm?6mm

2、轉動速度： 0-500轉/分 （可調）

3、負 荷： 196N ? 0.1%（可增至392N）

4、摩擦環尺寸：￠40?10mm ，倒角0.5?45?，外圓表面與內圓同心度偏差小于0.01

5、摩擦環材質：45號鋼,淬火,熱處理HRC40-45,外圓表面光潔度▼8

6、摩擦力矩： 0--4N?m

7、砝碼重量：4KG砝碼一件，1KG砝碼4件，可實現重量疊加功能。

Functional characteristics:

1, sample size: 30mm x 7mm x 6mm

2, rotation speed: 0-500 turn / points (adjustable)

3, load: 196N 0.1% (can be increased to 392N)

4, the size of the friction ring is: 40 x 10mm, chamfer 0.5 * 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.01.

5, friction ring material: 45 steel, quenching, heat treatment HRC40-45, round surface finish 8

6, friction moment: 0--4N. M

7, weight weight: 4KG weight one, 1KG weight 4, can achieve weight superposition function.

試驗報告

試驗報告應包括下列內容：

A.塑料名稱、規格、牌號、生產廠；

B.試樣的制備方法，摩擦表面狀況，測定的試樣個數；

C.環境溫度、溫度及狀態調節條件；

D.圓環材質、硬度、光潔度和外徑尺寸；

E.試驗負荷；

F.試驗結果：磨痕寬度或體積磨損及摩擦系數的測定結果；

G.試驗日期、人員。

Test report

The test report should include the following contents:

A. Plastic name, specification, brand, and manufacturer;

B. The preparation method of the sample, the condition of the friction surface, and the number of samples measured;

C. Environmental temperature, temperature and state regulation conditions;

D. Circular ring material, hardness, smoothness, and outer diameter size;

E. Test load;

F. Test results: Measurement results of abrasion width or volume wear and friction coefficient;

G. Test date and personnel.

精度Precision:

1、速度精度：1%

2、負荷精度：0.5%

3、摩擦力矩精度：1%

4、計數器精度：1S

5、傳感器測量精度：1% FS

Precision:

1. Speed precision: 1%

2. Load precision: 0.5%

3. The precision of friction moment: 1%

4. Counter precision: 1S

5. Sensor measurement accuracy: 1% FS

功能：

本廠生產的計算機控制塑料滑動摩擦試驗機是在現有電子塑料滑動摩擦試驗機的基礎上又增加了很多試驗功能，可以同時顯示扭矩-時間曲線，隨意設定試驗次數，顯示當前試驗次數，設定時間及當前試驗時間等多種功能，本機還配有彩色打印機，可以打印出帶有曲線，表格數據，試驗單位名頭的精美的試驗報告單。

Function:

The computer controlled plastic sliding friction test machine produced by our factory is on the basis of the existing electronic plastic sliding friction test machine, and has added a lot of test functions. It can display the torque time curve at the same time, set the test times at will, display the current test times, set the time and the current test time and other functions, this machine is this machine. It also has a color printer, which can print out exquisite test reports with curves, table data and test units.

試驗步驟

1、圓環應清除油污，貯存于干燥缸內以防生銹。

2、試樣經狀態調節后用感量為0.1毫克的分析天平稱取其質量（M1）。

3、把試樣裝進夾具，摩擦面用角尺校正并使它與圓環的交線外于試樣正中。裝好摩擦力矩記錄紙，開機校好零點。

4、再次用乙醇、丙酮等不與塑料起作用的溶劑仔細清除試樣和圓環上的油污，此后不準再用手接觸試樣和圓環的表面。

5、平穩地加荷至選定的負荷值。

6、對磨2小時后停機卸負荷，取下試樣和圓環，清理試樣表面后，用精度不低于0.02毫米的量具測量磨痕寬度，或在試驗環境下存放1小時后稱取試樣質量（m2)。

7、讀取摩擦力矩值。

Experimental steps

1. The circular ring should be cleaned of oil stains and stored in a drying cylinder to prevent rusting.

2. After adjusting the state of the sample, weigh its mass (M1) using an analytical balance with a sensitivity of 0.1 milligrams.

3. Insert the sample into the fixture, calibrate the friction surface with an angle ruler, and ensure that its intersection with the circular ring is outside the center of the sample. Install the friction torque recording paper and start the machine to calibrate the zero point.

4. Carefully remove the oil stains on the sample and the ring using solvents such as ethanol and acetone that do not work with plastic. After that, do not touch the surface of the sample and ring with your hands.

5. Smoothly load to the selected load value.

6. After grinding for 2 hours, stop the machine to unload the load, remove the sample and ring, clean the surface of the sample, measure the width of the grinding mark with a measuring tool with an accuracy of not less than 0.02 millimeters, or weigh the sample mass (m2) after storing it in the test environment for 1 hour.

7. Read the torque value of friction force.

狀態調節

狀態調節按GB2918-82《塑料試樣狀態調節和試驗的標準環境》進行，溫度為23?5攝氏度，溫度為50?10%。

摩擦磨損定義

1、摩擦：兩物體接觸表面間產生阻礙切向相對移動的現象稱為摩擦。

2、滑動摩擦：兩接觸物體接觸點具有不同速度時之摩擦。

3、摩擦力：兩物體摩擦時相對移動的阻力。

4、摩擦系數：阻礙兩物體相對運動的摩擦力對作用到物體表面的法向力之比。

5、磨損：物體相對運動時相互接觸表面的物質不斷損失或產生殘余變形稱為磨損。

Definition of Friction and Wear

1. Friction: The phenomenon of hindering tangential relative movement between two surfaces in contact is called friction.

2. Sliding friction: Friction between two objects in contact at different speeds.

3. Friction: The resistance to relative movement between two objects when they rub against each other.

4. Friction coefficient: The ratio of the frictional force that impedes the relative motion of two objects to the normal force acting on the surface of the object.

5. Wear: The continuous loss or residual deformation of substances on the surfaces in contact with each other during relative motion of objects is called wear.

主要配置及附件：（計算機控制）

1、試驗主機一臺

2、高精度扭矩傳感器一只

3、計算機數據采集卡一塊

4、計算機一臺（品牌）

5、彩色激光噴墨打印機一臺

6、計算機控制軟件一套

7、4Kg 砝碼兩件（備用一套）

8、標準磨擦環四件（備用兩件）

9、產品使用說明書一份

10、產品合格證

11、產品裝箱單一份

12、整機重量：約87 公斤

Main configuration and accessories: (computer control)

1. A test host

2. A high precision torque sensor

3. One piece of computer data acquisition card

4. One computer (brand)

5. A color laser inkjet printer

6. A set of computer control software

7, two 4Kg weights (a spare set)

8, four standard friction ring (two spare)

9. One copy of the product instructions

10. Product qualification certificate

11. Packing a single part of the product

12, the weight of the whole machine: about 87 kilograms

售后服務。

1、保修期內非人為損壞的零部件免費更換，保修期內接到用戶邀請后，最遲響應時間為4小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法。

2、提供實時的遠程診斷和維護服務。

3、每年進行客戶回訪。

4、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后2天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。

5、保修期內人為損壞的零部件按采購（加工）價格收費更換。

6、軟件升級：終生免費提供新版本控制軟件。

7、安裝及調試合格后，自客戶簽字認可之日起，我方對于提供的產品免費保修三年。保修期滿后，我方將繼續跟蹤服務，客戶享受終生維修，負責及時提供必要的售后服務、技術咨詢。

8、產品交貨期：盡量按用戶要求，若有特殊要求，需提前完工的，我公司可特別組織生產、安裝，力爭滿足用戶需求。

9、保修承諾：我司對本次協議供貨有效期內所提供的所有產品保質期 ，有效期內所提供的產品，提供正常工作日全天侯服務，終身技術服務支持。

10、響應時間：保修期內，產品若發生故障，在接到貴公司報修后，24小時內幫客戶解決問題。

11、服務體系：作為設備供應商本公司對本次招標所提供的產品提供保障體系： 當設備出現故障，必要時將派指定的專業技術員在規定時間內上門維修或寄修，產生的運費由本公司承擔。

12、產品價格承諾 1、在同等競爭條件下，我公司在不以降低產品技術性能、更改產品部件為代價的基礎上，真誠以最優惠的價格提供給貴方。 2、在保修期內供方將免費維修和更換屬質量原因造成的零部件損壞，保修期外零部件的損壞，提供的配件只收成本費，由需方人為因素造成的設備損壞，供方維修或提供的配件均按成本價計。

13、售后服務保證

公司實力保障：本公司有完善的售后服務體系;

公司承諾：

1.購機前，我們專門派技術人員為您設計的流程和方案

2.購機后，將免費指派技術人員為您調試安裝

3.整機保修一年，產品終身維護

4.常年供應設備的易損件及耗品確保儀器能長期使用

5、售后管理：我公司實現計算機化管理，實行客戶定期電話回訪制度，定期復查設備的工作情況，定期電話指導用戶對設備進行保養和檢測，以便設備正常運轉，跟蹤客戶的設備使用情況，以便及時對設備進行維護

6、物流情況：及時提供貨源，確保全國范圍內2-10內到貨，持續穩定地為代理商做全面服務工作，提供合理的運作空間。公司有專業的技術人員為您安裝指導。

7、軟件升級：終生免費提供新版本控制軟件。

8、安裝培訓:儀器包裝內附有說明書，專業培訓人員為客戶指定操作者講解儀器正常操作流程、操作注意事項及儀器的日常維護要求；也可以根據客戶要求提供上門培訓服務。

Products Description

[Product Name]is a high-quality product designed to meet the needs of businesses looking to[specific goal]. This product offers a range of features and benefits that make it an ideal choice for businesses of all sizes.

Features:

[List key features of the product]

[Include any technical specifications or design details]

Benefits:

[Explain how the product can benefit the customer's business]

[Include specific examples of cost savings, increased productivity, improved efficiency, etc.]

We believe that[Product Name]offers an unbeatable combination of quality, performance, and value. If you have any questions about this product or would like to learn more about how it can benefit your business, please don't hesitate to contact us. We are dedicated to providing excellent customer service and helping our customers achieve their business goals.

Thank you for considering[Product Name]. We look forward to the opportunity to work with you and help you achieve success.

FAQ

1.Q: What is the expected lifespan or durability of the product?

A: Our product has an expected lifespan of X years and is designed to withstand heavy use in industrial environments.

2. Q: What is your company's experience and reputation in the industry?

A: Our company has been in business for X years and has a reputation for delivering high-quality products and excellent customer service. We have worked with numerous clients in various industries.

3. Q: What is your company's policy on returns and refunds?

A: We have a flexible returns and refunds policy that allows customers to return products within X days of purchase for a full refund or exchange. We also offer warranties on our products to ensure customer satisfaction.

4. Q: Are there any certifications or standards that the product meets?

A: Yes, our product meets several industry certifications and standards, including [list certifications and standards].

Product Parameters

Product Name	Model Number	Dimensions

Recommend Products

Other related hot products that may be of interest to you.

List other products from the related categories.

Details Images